Thanks for the wonderful comments and emails on the Halloween posts. So glad you enjoyed them. Karianne at THISTLEWOOD FARMS has inspired me to come up with some cutout printables for Thanksgiving as well, so expect a project soon. Checkout Kari’s site over there. She is a Hoot! 🙂
With that said, I know I’m not the only one who’s glad that Halloween is done. The pumpkins are pooping out and any color other than orange, is much welcomed at this point. Still, it’s a bit odd that the BIG BOX stores are already decked out in red and green. What about that holiday in between? You know, the big Gobble-Gobble with the green bean casserole and pumpkin pie.
After my latest budget “fun finds”, I’m into some fun Thanksgiving designs. I found several great fabric pieces in the remnant bin at Wal-Mart. Two are for more easy make table runners, like the one I’ve already finished, pictured. The tutorial is at the end of this post.
The others are for another RAG WREATH . If you missed that post, check it out. I’m tickled to tell you that the Wreath for All Seasons was one of my most popular posts yet! A friend wants help making hers so thought I would do another along with her as a demo.
The wonderful works of world renowned artist MARIE THURMAN have inspired me to get creative with some decorative glass and ceramic ware. You’ll love this easy, inexpensive project. Found the perfect glass and plates to use, at my local Discovery Thrift Store. Article coming soon. Also coming up, a twenty-five cent TV tray will get a remarkable re-do and new use.
My continued search for cool, new blogger buddies means another “FEATURED FAVORITES” spot in the very near future as well.
But today, look how easy and inexpensive this table runner is to make. And it only takes about an hour.
I’m using two compatible fabrics and some decorative wired ribbon to make three runners that will criss-cross over the table top.
First, I cut the polka-dot fabric lengthwise, to create two equal pieces. Then I trimmed off the end edges.
Next I pressed the fabric with my iron on a low-steam setting. It had some heavy wrinkles, so I placed a lightly dampened wash-cloth over those areas and did another light press over. Just don’t have the wash-cloth too wet or the steam setting too hot.
Now, I cut four pieces of my metallic, wired ribbon; two that are two inches longer than the length sides, and two that are two inches longer than the width. You want your ribbon to have an extra inch on each end, so that you can miter/match your corners a bit later.
While my low temp glue gun was heating, I covered the top of my ironing board with wax paper. This will catch any glue goofs and protect the pad. Place your fabric FACE SIDE UP on the ironing board. Beginning on a length side of the fabric, I lined up my ribbon (with one inch hanging beyond the end) then pinned down the ribbon and pinned down a few areas of the fabric. TIP: be sure to allow a one inch overhang of ribbon, beyond the end of the fabric. AND start your glue line down an inch or so from the end of your fabric. You’ll have one inch of ribbon unglued to the fabric and one inch over hang.
Now begin to glue. I ran a very thin line of glue about a quarter inch in from the edge of the fabric, going as far as one glue pull would take me. Now begin placing the ribbon on top of the glue line, gently because it is hot.
Go back and pat down the ribbon onto the glue. Continue until you are an inch from the opposite end.
When your first edge is done, go back to the beginning and glue your inside edge, following the same procedure, placing glue about a quarter inch above the inside edge of your ribbon.
If you go crooked and off line with your glue, DON’T WORRY, just leave it alone for now. Correct your line and continue gluing.
When your ribbon is attached, and glue is dry, you simply go back to the extra glue on your fabric, rub back and forth a couple times and gently pull it up and snip it off.
Complete both glue lines of one length edge and then do your width edge next. BEFORE YOU BEGIN to glue this second ribbon piece, overlap your loose end pieces. Then cut a miter cut through both pieces. Pull away the excess ribbon and you’ll have a mitered corner. Now begin gluing this edge, following the same steps as before.
Do each remaining side in the same manner.
Here’s the final project.
FABRIC, cut to preferred width and length; this project was 13.25″ width by 43″ length.
GLUE GUN, low temp and 2 GLUE STICKS were used for this project
WIRED RIBBON; I used a 1 1/2 inch width ribbon.
IRON and IRONING BOARD
I’m going to make an identical runner, and then two long runners in the striped fabric. Not sure if I’ll use the same ribbon on those. One will be used in the table group, and the other in the next room on the piano, to keep the look going.
This is a quick and easy, economical project that can add a little perk to any table. I’m using mine for Thanksgiving! Let me know what you do with yours.
Later – Cheryl
This original article “Thanksgiving Thinking” appeared first on Artzzle.com.
Copyright © 2013 Artzzle All Rights Reserved
No included content or photography can be used elsewhere without specific permission from said originators.